Tools
Slab template calculator for cups, vases, bowls, plates and boxes
Enter the size you want the finished pot to be. The calculator draws every piece at actual size, made larger to allow for shrinkage, ready to print, cut out and lay on your slab.
What to cut
- Cut one wall piece (a curved strip, because the sides taper) and one base circle 114 mm across.
- The wall is 222 mm measured up the slope, and leans 3° in from upright.
- Roll the slab 6 mm thick. The wall stands on the base, so the base adds its thickness to the height.
- Built 13.6% larger than the finished pot, so it shrinks to size. Prints on 3 pages.
Building it
- Print the pages, and tape any pages that belong together: cut along the solid line on one page and lay that edge on the dashed line of the page before it, so the outline runs on unbroken.
- Roll a slab to the thickness you entered, a little bigger than all the pieces, and let it firm up until it bends without slumping or cracking.
- Lay the paper on the slab and cut around it with a needle tool or a sharp knife held upright. Cut the base circle too.
- Choose your seam. For a bevelled seam, hold the knife at about 45°, start on the paper line, and cut both ends parallel, so one end slopes under and the other slopes over; ignore the dashed strip. For an overlapped seam, cut the dashed 10 mm strip on as well and lay it under the other end.
- Score and slip both edges, curve the wall round, press the seam together, then compress it inside and out with a rib. A cardboard tube can help a vase keep its shape: wrap it in newspaper so it slides out, and take it out as soon as the wall stands on its own, because clay shrinks onto a tube left inside and cracks.
- If the wall leans out or in, cut its bottom edge at the same slant so it sits flat on the base. A wall leaning more than about 30° may need support, such as a bowl or a paper collar, until it firms up.
- Stand the wall on the base, score and slip where they meet, and press a thin coil into the inside corner; a wooden spoon handle reaches down a tall vase. If you can’t reach, smooth clay from the wall down over the join on the outside instead. Trim the base flush if it sticks out.
- For a mug, add the handle when the cup and the handle are both soft leather-hard: score and slip both ends, press them on, and blend the joins. Then cover the whole mug loosely, so the handle dries no faster than the cup. If it will hold food or drink, ask your studio which glazes they use for that.
- Dry it slowly and evenly under loose plastic on a board or newspaper. Once the rim is firm, turn the pot over for a while so the base dries as well.
Building it
- Find a mould the size shown above: a smooth, rounded bowl with no undercut. Line a plastic or glass bowl with cloth or a sheet of newspaper so the clay comes out. A plaster or bisque mould needs no lining, but it draws water out of the clay, so check the bowl sooner.
- Roll a slab to the thickness you entered and cut the circle. If you printed a quarter, trace it four times around the centre dot.
- Lift the slab over the mould, centre it, and ease it down inside the mould, from the middle outward, with a soft rib or sponge. Don’t stretch it, and don’t drape it over the outside of a bowl instead: clay drying over a mould shrinks onto it and cracks. Firm the floor with a rib from the centre out.
- Near the rim there is more clay than room, so it will gather into folds. Cut each fold out as a narrow wedge, then score, slip, join and compress the edges.
- Trim the rim level with the top of the mould. The dashed circle is a guide: the extra 10 mm beyond it is there so you can trim to an even rim.
- Leave it in the mould until it is leather-hard, then lift it out. A bowl’s rounded bottom rocks, so tap it gently flat on the table or add a coil foot ring, then let it finish drying slowly under loose plastic.
- A plate is wide and thin and warps easily. A mould with a flat floor gives it a flat bottom. Dry it slowly under plastic, keep the rim from drying ahead of the middle, and turn it over between two boards once the rim is firm.
Building it
- Roll a slab to the thickness you entered and let it firm up until it stands without bending; boxes go together best from stiffer, leather-hard slabs.
- Lay the paper pieces on the slab and cut around them with a needle tool or a sharp knife held upright, using a ruler for straight edges.
- Score and slip the base edge and the bottom of a long wall, then stand the wall on the base and press it down. Do the same with the second long wall.
- Score and slip the ends and bottom of each short wall, and the inside ends of the long walls where they meet, then fit the short wall between the long walls, standing on the base. Every outside edge should line up with the base.
- Press a thin coil into every inside corner and along the base, and compress the outside corners with a rib or a flat stick.
- Dry it slowly under loose plastic, on a board so the base stays flat. Corners dry first, so check them, and turn the box over once the rim is firm so the base dries as well. The template has no lid.
How the numbers work
A slab wall unrolls flat. A straight-sided cylinder becomes a rectangle as long as the pot is round. A vase or bowl that tapers is a slice of a cone, and its flat pattern is part of a ring: the more it tapers, the more the strip curves. The calculator works out that ring from your rim and base sizes, measuring around the middle of the slab’s thickness, because that is the line that neither stretches nor squashes when the slab bends.
The wall stands on top of the base, so it is cut one slab-thickness shorter than the pot. Everything is then made larger to allow for your clay’s shrinkage: the template is drawn at the size you build, and the pot shrinks to the size you entered as it dries and fires. That uses the same sum as our shrinkage notes: divide the finished size by one minus the shrinkage.
A rounded bowl or a plate pressed into a mould starts as one flat circle. Its radius is the distance from the middle of the floor, up the curve, to the rim, so a deeper bowl needs a bigger circle than its rim size suggests. A bowl can be at most half as deep as it is wide, or it won’t come out of the mould.
A box is five flat pieces. The two long walls run the full length of the base, and the two short walls are cut two slab-thicknesses shorter so they fit between them. Cups and mugs use the same wall maths as a vase, just smaller.
Before you rely on it
The patterns are geometry: they come out the size you entered if your clay shrinks as much as the number you typed and your slab bends without stretching. Real slabs stretch a little as you handle them, so make a first one from scrap clay or card if the size matters. Joins are where slab pots usually fail; our notes on why handbuilt joins separate cover how to make a seam that holds. To check how much a pot will hold, or how much clay to weigh out, use the vessel calculator.