Clay & Forming · Troubleshooting

Why Handbuilt Clay Joins Crack or Separate

7 min read

Clay Manual · Research notes · Published October 19, 2026 · Updated October 29, 2026

Drawing: a leather-hard clay mug whose paler handle has pulled away from the wall at its top join, leaving a small crack.

With one of us drawn to handbuilding, joining pieces of clay is a topic that fits naturally into our reading. A handle, a coil, and a slab corner can all raise the same question: what helps the parts stay together?

We are collecting research notes here, not presenting our own proven joining method. If a join opens, when it happened is a useful detail to take to an instructor.

Short answer

Why did the join separate?

First write down when you noticed it: while the clay was soft, while it was drying, after it was dry, or only after firing. A join between two pieces at different moisture levels is a drying-gradient problem in Hansen’s sense: one part shrinks after the other has stiffened. A line that appears only after firing may be a different problem. This page does not certify a joining method.

Handbuilt parts — a coil and a wall, a handle and a cup, a slab corner — fail in more than one way. Treating every opened join as “not enough slip” hides the cases that are really about moisture, thickness, or a crack that was already there before the kiln.

Hand-drawn diagram of four cups with handles, one for each stage when a join can open: while soft (maybe not pressed into one piece), while drying (a handle or coil can dry ahead of a thicker wall), after it was dry (it may have started earlier, or been bumped), and only after firing (a drying crack, or a mismatch you did not see). Each stage has a next step, and a note says two parts at different moisture levels means one shrinks after the other has stiffened.
When you first noticed the opened join points to different causes and different people to ask.

The stage diagram is a labeling aid. It is not a photograph of a failed pot, and leather-hard here means a handling description, not a firing target.

Start with when it happened

Join problems by the stage when you first saw them.
What you seeCondition to checkWhat to recordNext safe action
The parts never held while both were softThe surfaces may not have been pressed into one piece. That is a handling question for the instructor watching the next join, not a diagnosis this page can make from a photo.How soft each part was, and whether they were supported while you joined them.Ask the instructor to watch one join. Do not treat a written tip as a substitute for that demonstration.
The join cracks while the piece is dryingHansen’s account of uneven shrinkage fits a join where one part stiffened first. A handle or a coil can dry ahead of a thicker wall.Which part lightened or felt firmer first, and whether air hit that part.Record it, then even out the next drying setup if the studio agrees. Do not sand the dry join. See the drying guide for the dust limit.
A crack is visible only once the piece is already dryIt may have started earlier as a gradient, or the dry piece may have been bumped. The page cannot assign a single cause.Whether the piece was moved, and whether the two sides of the join were the same clay and similar thickness.Photograph it and show the instructor. Do not wet a bone-dry join and expect it to reknit.
The line shows up only after firingA drying crack can open in the kiln, and so can a mismatch you did not see. Different clays shrink differently. This is no longer only a wet-work question.Both clay names, the stage notes, and the cone the studio recorded, with the leading zero if there was one.Do not change a firing schedule from this table. Ask the kiln technician. Do not decide the pot is safe or unsafe for food from the crack alone.

How a join is usually made so it holds

This is what a university course text, a Skutt teaching lesson, two magazine articles and Tony Hansen’s technical notes describe. It is not a proven method of ours, and the method your instructor teaches in that studio comes first.

Cross-section of a handle end joined to a cup wall, both leather-hard: both surfaces scored, a thin slip layer between them, the seam pressed and smoothed, and a small coil rounding the angles above and below the handle.
Diagram: a scored-and-slipped handle join in cross-section. Handle and wall both leather-hard, only enough slip, the seam compressed, and a small coil rounding the angles above and below the handle.

Join leather-hard to leather-hard. Tony Hansen’s Digitalfire glossary entry on leather-hard clay puts attaching handles, spouts and other components at the medium stage, and assembling slabs at the stiff end of leather-hard. In a slab-box lesson published by Skutt, teacher Jennifer Fowler notes that students struggle to find the right stage of clay for slabs: too soft and floppy, or too hard to join. Hansen’s drying notes add that no part of a piece should be significantly ahead of another, and that a stiffer part cannot shrink with a softer neighbor. In a Digitalfire caption about mugs from sixteen kinds of clay that came through drying without cracking, he says to make the handles a while after the mugs, because handles stiffen quicker.

Coil building is different: in Jessica Fong’s ceramics course text for the University of the Pacific, new coils go onto lower layers that have only been allowed to stiffen slightly, and the coils waiting their turn are kept wrapped in plastic so they don’t dry.

Score both surfaces. Fong’s course text says to score and slip each coil before attaching it, and names the needle tool as a scoring tool. Fowler’s students score each cut side of a slab before adding slip. In Ceramics Monthly, Tania Rustage scores with a wire-brush tool or the edge of a serrated rib and applies slip to both the cup and the handle before attaching. Our tools guide explains what a needle tool and a rib are for. Hansen puts more weight on pressure: he calls a join method that lets you apply lots of pressure better than scoring. His caption doesn’t name that method or tell you to skip scoring, and it is about thrown mugs. Ask your instructor how that studio does it.

Use only enough slip. Hansen asks for only enough slip, of thick cream consistency, to make the join, with no excess squirting out at the edges, and any excess wiped away. On another of his picture pages, about one mug, he blames a split on excess slip left around the handle join: on a clay with larger particles, he says, surface water can seep in and start a split. Whether a thicker joining paste works better than slip is a separate question, and this page does not answer it.

Press and compress the seam. Fowler has her students squeeze the joined edges together at the outer corner. Fong describes smoothing the interior and exterior seams of a coil-built form for strength. In Pottery Making Illustrated, Katie Sleyman joins parts by scoring, slipping and compressing. She drags a rubber-tipped tool along the seams between the joined segments of a bottom to compress them slightly to help prevent cracks, and supports the clay from the other side while she refines a seam.

Add a small coil where the parts meet. Rustage rolls a thin coil, places it around each handle join, and rolls it smooth with a small dowel. Fowler’s lesson adds a coil to the inside of the bottom of the box. That fits Hansen’s note that drying cracks like to start inside sharp angles, and that rounding those angles at handle joins while the clay is leather-hard denies a crack a place to start.

Dry it evenly, and slowly if that helps keep it even. Hansen puts evenness ahead of speed: fast-but-even drying gives fewer cracks than slow-but-uneven drying. He recommends covering ware with cloth and plastic, and waxing or wrapping handles so they keep pace with the body. In the split he describes, the handle had been allowed to dry faster than the mug, pulling at the join. Sleyman covers a finished form in plastic overnight so its moisture evens out, then lets it dry slowly. The drying-crack guide covers the rest of a drying setup.

None of this tells you that a particular join is sound. If a join still opens, the stage table above is where to start.

What a careful record adds

Write the two moisture descriptions in the log at the time you join, not the next week. Hansen’s stage names (soft, medium and stiff leather-hard) give you words for them. If you also measure a bar of that clay, the shrinkage guide tells you the percentage for a named stage. It still does not tell you that the join was sound.

When to ask an instructor

A craft instructor can review whether your joining matches the studio’s method. That review is recommended before anyone treats this page as teaching material. It has not happened yet. An instructor’s review of a join would not qualify them to approve kiln wiring or a food-contact claim.

The drying-crack checks cover cracks that are not on a join. Our clay dog project scores and slips every join on a small pinch-pot piece. Class preparation is where you ask who is allowed to help you fix a piece in that studio.

What we are taking from this

Pay attention to the stage and the condition of both parts. An instructor watching the process can offer context that a written checklist cannot.

Sources (10)

: Digitalfire, Tony Hansen, Jessica Fong, University of the Pacific, on Humanities LibreTexts, Skutt, lesson by teacher Jennifer Fowler and more
  • Drying Ceramics Without Cracks — Digitalfire, Tony Hansen. Ware shrinks when it dries; Isolate the stage where drying gradients are introduced; Give consideration to each type of piece; Clay is composed of microscopic flat crystals; Conclusion; and the picture notes on mugs, handles and foot rings. Supports: Hansen says it is the unevenness of drying, not its speed, that makes ware crack, and that at no time should any part of a piece be significantly ahead of another. A moisture spread introduced early (for example by an unshielded draft, or ware left out too long after forming) tends to remain, and in one of his examples covering mugs with cloth and plastic after the rims had stiffened did not save them. He recommends covering ware with cloth and plastic, waxing or wrapping handles so they keep pace with the body, slowing fast-drying sections with wax resist or latex at leather-hard, turning bowls over as soon as possible, even wall thickness with bases trimmed to the same thickness as the walls, avoiding sharp concave angles, and compressing the bottoms of wide thrown pieces to reduce drying stress (while saying even thickness and even drying, not compression, are the key). His conclusion: take cracked ware seriously, because a few cracked pieces can reveal a flawed process. The article gives no method for repairing a crack that has already opened. This is a technician's published explanation, not a test run for this site.
  • Drying Crack — Digitalfire, Tony Hansen. Glossary text and picture notes on S-cracks, handle joins and large plates. Supports: Hansen says evenness matters more than drying speed and that fast-yet-even drying gives fewer cracks than slow-but-uneven drying. He says drying cracks like to start inside sharp acute angles, so rounding those angles at handle joins while the clay is leather-hard denies a crack a place to start, and that thinner, more even walls, better wedging and more even drying mean fewer cracks in large plates. He says most shrinkage happens as the first water is released, and that when one part dries well ahead of a neighboring part the stiffer part cannot shrink with the softer one. The entry describes S-cracks growing suddenly near the end of drying. It does not explain how to repair a crack that already exists.
  • 2.2: Essential Tools and Their Uses — Jessica Fong, University of the Pacific, on Humanities LibreTexts. Basic Tools: needle tool and rib tool. Supports: The needle tool is one of the most versatile tools in ceramics, used for scoring, trimming, and measuring. Rubber ribs compress the clay surface on the wheel to prevent cracks; wooden ribs are lightweight and suit shaping hand-built pieces; metal ribs are more rigid, for trimming excess clay during throwing.
  • Leather hard — Digitalfire, Tony Hansen. Glossary text on soft, medium and stiff leather-hardness. Supports: Hansen describes three leather-hard stages. At soft leather-hardness pieces can still tolerate some bending, reshaping and assembly. Medium leather-hardness is the stage where pieces are trimmed and fettled most easily and handles, spouts and other components are attached. Assembling slabs is done at the stiff end of leather-hardness. The entry does not give a joining method or say how to match the moisture of two parts. This is a technician's published glossary, not a test run for this site.
  • Strange drying crack on a porcelain mug — Digitalfire, Tony Hansen. Picture caption (drying crack on the inside of a mug at the handle join) and the related picture caption shown on the page, Sixteen kinds of clay. No mugs have cracked in drying. Why?. Supports: The main caption shows a drying crack on the inside of a mug at the handle join. The related caption on the same page, about thrown mugs from sixteen kinds of clay that did not crack in drying, advises making the handles a while after the mugs because handles stiffen quicker, applying them once the rims hold their shape, using a join method that enables application of lots of pressure (which Hansen calls better than scoring, without naming the method or saying to skip scoring), and using only enough slip, of thick cream consistency, to make the join, with no excessive squirting out at the perimeter. It also advises throwing walls of even thickness, trimming bases to the same thickness as the walls, and covering the mugs with cloth and plastic. The timing it gives is tied to Hansen's own climate. This is a technician's published account, not a test run for this site.
  • This appears to be a drying crack, but it is not — Digitalfire, Tony Hansen. Picture caption. Supports: Hansen describes one mug where a split near the handle ran into the mug wall rather than along the join. Excessive slip around the join had not been removed, which he says is bad when a body has larger particles, because surface water can seep in and start a split. An aggravating factor was that the handle was allowed to dry faster than the mug, pulling at the join. It is one example, not a general rule, and the caption does not discuss scoring or pressure.
  • 4.2: Coil Construction - Pottery and Sculpture — Jessica Fong, University of the Pacific, on Humanities LibreTexts. Coil construction steps and tips. Supports: Fong says to score and slip each coil before attaching it to ensure strong adhesion, to attach coils layer by layer while smoothing the interior and exterior seams for strength, to blend seams between coils with fingers or a rib tool, to let lower layers stiffen slightly before adding more coils, and to wrap coils in plastic while working to prevent drying. The page does not mention leather-hard clay or reinforcing a seam with a separate coil.
  • Slab Box with Roofing Paper Template — Skutt, lesson by teacher Jennifer Fowler. Project Description; Demo & Do parts 2 to 5 (build sides, top and bottom, remove template, cutting lid); Meet The Teacher. Supports: The lesson says students struggle with finding the right stage of clay to build with slabs, either too soft and floppy or too hard to join. Building the sides, students score each side they just cut, then add slip, and put two angled edges together squeezing them at the outer corner; the top of the box is also scored and slipped. The clay should be stiff leather-hard by the time the templates are removed, after the box is assembled; keeping the template on helps retain moisture. Later, a coil can be added to the inside of the bottom of the box. The page has no byline (the teacher is named under Meet The Teacher) and shows no canonical or permalink address; this ?p= address is the one search engines list and the one that was read.
  • Tips and Tools: Foolproof Handles, by Tania Rustage — Ceramics Monthly (Ceramic Arts Network), October 2021. Steps for making and attaching the handle. Supports: Rustage scores with a wire-brush tool or the edge of a serrated rib and applies slip to the cup and the handle before attaching, using vinegar on an old toothbrush to make the slip and scoring twice. After attaching, she seals the edges of the attachment with a small dowel or skewer, rolls out a thin coil, places it around the joins, and rolls the dowel to make a smooth attachment, repeating this at the lower attachment. The article gives no drying instructions for the join. The page is metered; its full text was shown as a complimentary article.
  • In the Potter's Kitchen: A Custom Container, by Katie Sleyman — Pottery Making Illustrated (Ceramic Arts Network). Construction steps for the body, seams and scalloped bottom. Supports: Sleyman scores both beveled cuts, applies slip (or vinegar or water) and presses or compresses the parts together, using a piece of wood to counter the pressure from the other side while she refines a seam. She joins the segments of the scalloped bottom by scoring, slipping and compressing, and drags a rubber-tipped tool along the seams between the lobes to compress them slightly to help prevent cracks. Once the piece is leather-hard she cleans up the bottom seam, covers the form in plastic overnight so its moisture content evens out, and allows the piece to dry slowly. The page is metered; its full text was shown as a complimentary article.