Clay & Forming · Troubleshooting

Why Does Clay Crack While Drying? Causes and Prevention

5 min read

Clay Manual · Research notes · Published October 19, 2026 · Updated October 23, 2026

Drawing: a clay mug drying on a table, pale at the rim and handle and darker toward the thick base, with a small crack running down from the rim.

Short answer

Why does clay crack while drying?

Clay shrinks as it dries. A crack usually means one part dried, stiffened and shrank ahead of a neighboring part, and the pull between them was more than the clay could take. Tony Hansen’s drying notes put evenness ahead of speed: fast-but-even drying gives fewer cracks than slow-but-uneven drying. To prevent it:

  • Dry the whole piece evenly. No part should get significantly ahead of another. Shield the piece from a draft that hits only one side.
  • Slow down the parts that dry first. Cover the piece with cloth and plastic, and wax or wrap handles so they keep pace with the body.
  • Keep thickness consistent. Aim for even walls, with bases trimmed to about the same thickness as the walls.
  • Round off sharp inside angles at joins while the clay is leather-hard, because cracks like to start there.
  • Let the base catch up. Turn bowls over as soon as they can take it. On wide thrown pieces, compress the bottom.
Hand-drawn diagram of a cup whose rim and handle dry first while the thick base is still soft, with a crack where the pull was more than the clay could take. Beside it, five ways to prevent it: dry the whole piece evenly, slow the parts that dry first, keep thickness consistent, round off sharp inside angles at joins while leather-hard, and let the base catch up.
A crack usually starts where one part dried ahead of another, so each fix aims at even drying.

All of this comes from the sources listed below. We have not tested it on our own pieces. Hansen also writes about changing the clay recipe, but that is beyond a beginner class, so we do not repeat it here as instructions.

Why uneven drying causes cracks

Most of the shrinking happens as the first water leaves the clay. If a rim or handle stiffens while the base is still soft, the stiff part can’t shrink along with the soft part, and the stress has to go somewhere. Hansen points out that a moisture difference set up early, from a draft or from leaving a piece uncovered too long after forming, tends to stay for the rest of the drying. In one of his examples, he covered mugs with cloth and plastic after their rims had already stiffened, and they still cracked. So it pays to start drying evenly from the beginning rather than trying to rescue a piece later.

The S-shaped crack across a base is Hansen’s classic sign of uneven drying. It almost always means the rim dried ahead of the base. He notes these cracks can grow suddenly near the end of drying.

What to check

Drying-crack checks. None of these rows is a promised repair.
What you seeCondition to checkWhat to recordNext safe action
A crack at the rim while the base still felt softerThe rim may have dried, and shrunk, ahead of the base. Hansen calls this kind of gradient a common setup for cracks, including the S-shaped base crack when the rim gets ahead.Where air moved, whether a fan or a window hit one side, and whether you covered the rim and the base differently.Make the next piece dry more evenly if the studio allows it. Slower is not automatically safer. Do not change a shared studio’s racks on your own.
A crack running from a thick bottom or a thick join into a thin wallLarge differences in thickness dry and shrink on different clocks. Hansen uses cross-section differences as a practical warning.Rough thicknesses, and whether the thick part was still cool or dark when the thin part had lightened.Ask the instructor about the next piece’s thickness. Do not sand bone-dry clay to thin it. Princeton warns that sanding greenware makes silica dust.
An S-shaped crack in the baseHansen describes the S-crack as a classic sign of uneven drying, often a rim that stiffened before the base.Photographs, the drying spot, and whether the foot was on a non-absorbent board.Record it in the log and show the instructor. See the section below on cracks that have already opened.
Several pieces from one bag crack, and pieces from another bag do notThe body may differ, but the drying setup may differ too. Do not assume the clay is the only change.Clay name, lot, and the drying notes for both groups.Keep the log. Do not alter a studio body recipe. A manufacturer shrinkage figure is not your measurement unless the stage matches.
The crack is obvious only after firingIt may be a drying crack that opened later, or a different problem. This page cannot tell those apart from a description.Whether a hairline was already visible when the piece was dry, plus the cone the studio recorded.Stop. Do not invent a new firing schedule. Ask the person who runs the kiln, and keep the food-use question separate from this crack.

Can I fix a crack that already opened?

For pottery clay that will be fired, our sources don’t give a repair method. Neither of Hansen’s pages explains how to mend a drying crack once it has formed, and we won’t make one up. What Hansen does say is to take cracked ware seriously: even a few cracked pieces can point to a flaw in the drying process, and luck may be the only thing that spared the rest. So the most useful thing to do with a cracked piece is to work out where the drying went uneven, and change that on the next piece. If you want to try saving the piece itself, ask your instructor or whoever fires the kiln first. They know the clay and the firing, and we can’t judge either from here.

Air-dry clay that won’t be fired is a different case. See the next section.

Air-dry clay at home

Air-dry clay cracks for the same basic reason: it shrinks as its water evaporates. Mont Marte, which makes air-dry clay, says cracks are common and are not a sign you did something wrong. Its advice:

  • To prevent cracks, let the piece dry completely and evenly. Turn it partway through drying, or set it on a wire rack like a cake cooling rack, so every side gets air. Don’t make the clay too thin. Mont Marte suggests about 1 cm.
  • To fix a crack, wet the area with a little water, using a fingertip or a wet brush. Press a small piece of fresh clay (ideally the same color) into the crack, smooth it with a wet brush, and let the piece dry completely before painting.

Those instructions are for air-dry clay only. Don’t assume a patch like this will hold through a kiln firing on pottery clay. Brands differ, so check the instructions for the clay you bought.

Where this page stops

  • It will not give a drying recipe that works for every clay.
  • It will not tell you to add grog or change a body formula.
  • It will not tell you to sand the crack out of dry greenware.
  • It will not give a firing schedule.
  • It will not convert the crack into a food-safety judgment.

Measure the next test piece with the shrinkage guide so you know how much that clay shortened under your setup. If the crack follows a join, use the join checks as well. Write both in the log.

A craft instructor should review technique before you teach this table to someone else. That review has not happened yet for this page.

Sources (4)

: Digitalfire, Tony Hansen, Princeton University Office of Environmental Health and Safety, Mont Marte (air dry clay manufacturer), Projects & How-to, 19 Aug 2021
  • Drying Ceramics Without Cracks — Digitalfire, Tony Hansen. Ware shrinks when it dries; Isolate the stage where drying gradients are introduced; Give consideration to each type of piece; Clay is composed of microscopic flat crystals; Conclusion; and the picture notes on mugs, handles and foot rings. Supports: Hansen says it is the unevenness of drying, not its speed, that makes ware crack, and that at no time should any part of a piece be significantly ahead of another. A moisture spread introduced early (for example by an unshielded draft, or ware left out too long after forming) tends to remain, and in one of his examples covering mugs with cloth and plastic after the rims had stiffened did not save them. He recommends covering ware with cloth and plastic, waxing or wrapping handles so they keep pace with the body, slowing fast-drying sections with wax resist or latex at leather-hard, turning bowls over as soon as possible, even wall thickness with bases trimmed to the same thickness as the walls, avoiding sharp concave angles, and compressing the bottoms of wide thrown pieces to reduce drying stress (while saying even thickness and even drying, not compression, are the key). His conclusion: take cracked ware seriously, because a few cracked pieces can reveal a flawed process. The article gives no method for repairing a crack that has already opened. This is a technician's published explanation, not a test run for this site.
  • Drying Crack — Digitalfire, Tony Hansen. Glossary text and picture notes on S-cracks, handle joins and large plates. Supports: Hansen says evenness matters more than drying speed and that fast-yet-even drying gives fewer cracks than slow-but-uneven drying. He says drying cracks like to start inside sharp acute angles, so rounding those angles at handle joins while the clay is leather-hard denies a crack a place to start, and that thinner, more even walls, better wedging and more even drying mean fewer cracks in large plates. He says most shrinkage happens as the first water is released, and that when one part dries well ahead of a neighboring part the stiffer part cannot shrink with the softer one. The entry describes S-cracks growing suddenly near the end of drying. It does not explain how to repair a crack that already exists.
  • Ceramics — Princeton University Office of Environmental Health and Safety. Clay hazards and precautions, and the lead-leaching section. Supports: Separate work clothes that do not trap dust, wet cleanup of clay scraps, and avoiding dry sanding of greenware are occupational precautions. A lead-safe label is not the same as a lead-free material, and craft studios do not automatically match industrial leaching tests.
  • How to: fix cracks in air drying clay — Mont Marte (air dry clay manufacturer), Projects & How-to, 19 Aug 2021. Why does air dry clay crack?; How to fix cracks in air dry clay; How to keep air dry clay from cracking. Supports: Mont Marte says air dry clay cracks because it shrinks as its water evaporates, and that cracks are common. To fix one, it says to moisten the area with a little water (fingertips or a wet taklon brush), press in a small piece of fresh clay, smooth it with a wet brush, and let the piece dry completely. To prevent cracks, it advises letting the piece dry completely and evenly, turning it partway through drying or using a cake-style drying rack, and not making the clay too thin, aiming for about 1 cm. This is a manufacturer's how-to for air dry clay, not guidance for kiln-fired clay, and it was not tested for this site.