Halloween · seasonal project
Clay & Forming · How-to
How to Make a Clay Ghost Tealight, Air-Dry or Kiln-Fired
10 min read
We know it’s late in the season. Our pumpkin and ghost totally won’t be ready in time for this Halloween, but it’s a cute night in the studio to get into the spooky-season mood, and we’ll definitely be decorating the house with them next fall.
A little clay ghost is one of the easiest Halloween pieces to make. It is a single slab of clay draped over a ball, like a sheet over a head, with two eye holes cut out. Set it over a tea light and the face glows.
You can make it from the clay you use in class and have it fired, or from air-dry clay at the kitchen table. The shaping is the same. What changes is how it dries, how it is finished, and what you put inside it. Our ghost isn’t finished yet, so the steps below come from course material, a ceramics magazine and clay makers’ own advice, which we link as we go, plus general studio practice where we say so.
Short answer
How do you make a clay ghost tea light?
- Make a soft form: set a crumpled newspaper ball, about the size of an orange and wrapped in plastic, on a short cup or jar, on a sheet of newspaper.
- Roll an even slab: lay a string from the table, over the top of the ball and down to the table on the other side, and cut a circle of clay that wide plus a little extra.
- Drape it: lay the slab over the ball and let it fall straight or flare out in soft folds, never tucked in under the ball, then trim the hem level so it stands.
- Cut the face: once the clay holds its shape, cut two eyes and a mouth, then lift the ghost off the form before it gets firm.
- Dry it slowly and evenly, then fire studio clay at your studio, or let air-dry clay harden at home.
Leave the bottom open so it sits over the light. Use a battery-operated LED tea light. Air-dry clay must never go near a real flame.
Which version should you make?
- Kiln-fired: use the clay your studio sells and fires. The ghost goes through a bisque firing, then a glaze firing if you glaze it. That needs a kiln, so most beginners take it to their class or a community studio.
- Air-dry: use an air-dry clay such as DAS, which FILA says hardens in air without baking. Creative Paperclay works too. You don’t need a kiln, but the finished ghost is decoration only. Air-dry clay isn’t waterproof or food-safe, and Mont Marte, which makes one, says not to bake it in an oven or kiln. Our air-dry clay guide compares three clays.
If you would like to try DAS, this is the white block we link in that guide.
What you need
- Clay: about 850 g (just under 2 lb) of studio clay, or about 1.4 kg (about 3 lb) of air-dry clay, for an orange-sized ghost. Step 2 shows where these numbers come from.
- A ball for the form, about the size of an orange, that gives a little when you squeeze it: a ball of crumpled newspaper works well. Avoid a rigid foam or plastic ball. Clay shrinks as it dries, and a form that can’t give can crack it.
- A plastic bag or plastic wrap to cover the newspaper ball, so the damp clay doesn’t stick to the paper.
- A short cup or jar to hold the ball up off the table.
- A sheet of newspaper or a board to build on.
- A piece of string and a ruler or tape measure.
- A rolling pin, and two strips of wood or two stacks of card the same height, to roll an even slab.
- A needle tool or craft knife, a drinking straw for round eyes, a fork or scoring tool, and a small sponge.
- A battery-operated LED tea light.
1. Set up the form
Crumple newspaper into a firm ball about the size of an orange and put it in a plastic bag, or wrap it in plastic wrap, twisting the excess underneath. Lay a sheet of newspaper on the table, or work on a board, so the damp hem doesn’t stick to the table and crack as it shrinks. Stand the cup on it upside down or right way up, whichever gives you the height you want, and rest the ball on top. The ball becomes the ghost’s head, and the cup sets how long the body hangs.
Keep your LED tea light nearby. You will check it fits the ghost’s opening once the ghost is off the form. Clay shrinks as it dries. Hansen at Digitalfire puts a typical pottery clay at about 6% in drying, before any firing shrinkage, so leave some room. Our note on measuring clay shrinkage explains how to find the number for your clay.
2. Roll an even slab
Roll the clay out between your two guide strips so the slab is the same thickness all over. For studio clay, about ¼ inch (6 mm) is the wall thickness the University of the Pacific course aims for in a pinch pot. Mont Marte says not to roll air-dry clay too thin, and suggests about 1 cm.
Even thickness matters more than the exact number. The same course says to keep thickness consistent to cut down stress during drying and firing, and Hansen says uneven drying, not fast drying, is what cracks ware.
To size the slab, lay a piece of string from the table, up over the top of the ball and down to the table on the other side. Cut a circle of clay that wide plus a little extra for trimming. For an orange-sized ball (about 75 mm across) on a cup about 60 mm tall, the string comes to roughly 29 cm, so cut a circle about 30 cm (12 inches) across.
That also tells you how much clay to start with. A 30 cm circle rolled about 6 mm thick takes roughly 850 g of studio clay. Air-dry slabs are usually rolled thicker, so at about 1 cm you need roughly 1.4 kg. That is more than one 1 kg block, so for air-dry clay a smaller ball or a shorter cup makes a smaller circle and saves clay.
Don’t leave the slab sitting out. Lauren Sandler, writing for Ceramic Arts Network, warns that a slab left to get too dry will crack when you drape it.
3. Drape the ghost
Lift the slab with both hands and lay it centered over the ball. Press it gently around the top so the head is smooth, then let the rest fall. Guide it into a few soft folds with your fingers, like a sheet.
Let the drape hang straight down or flare out below the ball. Don’t tuck it in under the ball. If the clay curls in underneath, the ghost locks onto the form and can’t be lifted off without tearing.
Try not to pinch the folds into thick doubled ridges. A fat fold is a thick spot, and thick spots dry more slowly than the thin wall beside them.
Trim the hem with your needle tool so the ghost stands level on the table. A wavy hem looks good, as long as it still sits flat.
4. Cut the face and lift it off
Let the ghost firm up on its form. Sandler waits until a draped slab has stiffened enough to hold its shape before trimming it and lifting it off. That is a good time to cut the face, too. The clay is soft enough to cut cleanly, but firm enough not to sag.
Push a straw through the wall for round eyes, or cut ovals with the needle tool. A mouth is optional. Smooth the cut edges with a damp sponge.
Then lift the ghost off, once it holds its shape and before it gets firm. Clay keeps shrinking as it dries, and even a soft newspaper ball holds it back, so don’t leave it on the form until it is bone-dry. If it sticks, squeeze the newspaper ball through the opening so it gives, then lift. Set the ghost back down on its newspaper or board to dry.
Now check the tea light. Measure the narrowest inside width of the ghost’s opening and make sure the light is narrower, with room to spare. A fired ghost shrinks again in the kiln.
For a kiln-fired ghost, the form must all come out. The University of the Pacific course says to remove a hard armature unless it is designed to stay in during firing. An open-bottom ghost slides off, which is one reason we like this shape.
5. Add arms, if you like
Two small, flattened coils make arms. With studio clay, score and slip both surfaces, press the arm on, and blend the edge. The course says to score and slip every connecting surface. Our note on why handbuilt joins separate explains why pressing alone isn’t enough.
With air-dry clay, Mont Marte says slip made from the clay and water works as a glue. It also warns that small pieces pressed on may fall off once the clay dries, and suggests craft glue for those.
Keep the arms close to the body and not much thicker than the wall. Thin, sticking-out parts dry first, and that is where joins crack.
6. Dry it slowly
Dry the ghost evenly. It doesn’t need to dry fast.
- Studio clay: cover the ghost loosely with plastic for the first few days, and open it up gradually. Hansen recommends wrapping thin parts, such as handles, so they keep pace with the body. A small piece of plastic over each arm does the same job. Our notes on why clay cracks while drying go into more detail.
- Air-dry clay: Mont Marte says to dry it gradually at room temperature, away from direct heat and sunlight, and suggests turning a piece at about 24 hours. On an open-bottom ghost, that means tipping it on its side for a while so the inside dries too. Creative Paperclay says small, thin pieces may dry overnight, while larger or thicker pieces can take several days.
7. Finish it
Kiln-fired: once the ghost is completely dry, take it to your studio for bisque firing, then glaze it and have it fired again. Follow your studio’s rules for which glazes to use. Wipe all glaze off the hem with a damp sponge before it goes back. The ghost stands on that edge in the kiln, and glaze left on a bottom edge melts and fuses it to the kiln shelf in a cone 6 glaze firing. Clay King, a ceramics supplier, describes the same order: a bisque firing, then another after glazing. Because the bottom is open, no air is trapped inside. If you ever close a hollow shape completely, the same course says to cut a small vent hole so it doesn’t burst during firing.
Air-dry: wait until it is completely dry, then paint it. Mont Marte suggests acrylic paint, and Creative Paperclay recommends a spray lacquer or brush-on varnish if you want to seal it. Sealed or not, keep it indoors and away from water.
What to put inside
Use a battery-operated LED tea light. For air-dry clay this is a must: Mont Marte says its clay is not suitable for direct contact with an open flame or high heat, and recommends an LED tea light for lanterns and candle holders.
For a fired ghost, we would still use an LED light. NFPA advises a battery-operated candle or glow stick in jack-o’-lanterns, and says nearly one-third of home fires that start with decorations are started by a candle. An LED light also keeps the inside clean and lets you leave the ghost on a shelf.
A quicker pinch-pot ghost
If you don’t have a ball and cup, pinch one. Make a deep pinch pot with walls about ¼ inch thick, turn it upside down, and gently stretch the rim into a wavy hem. Cut the eyes once it holds its shape. The bottom stays open, so the drying and lighting steps are the same.
More Halloween clay
For a pumpkin to sit beside your ghost, see our clay jack-o’-lantern, made from two pinch pots, with a free printable pumpkin face template. If you would like another small handbuilt animal after that, try the clay dog template.
Keep an eye out for our upcoming Christmas templates and articles!
Sources (12)
: Ceramic Arts Network (Ceramic Arts Daily), article by Lauren Sandler, first published 2015, University of the Pacific (Jessica Fong, Ceramics course on Humanities LibreTexts), Digitalfire, Tony Hansen and more
- Forget the Plaster: How to Make a Surprisingly Durable Hump Mold out of Unfired Clay — Ceramic Arts Network (Ceramic Arts Daily), article by Lauren Sandler, first published 2015. Draping and removing the slab. Supports: Sandler says not to let a slab get too dry before draping it, or it will crack when draped over the mold. Once the slab has stiffened enough to hold its shape, she trims the excess clay from the bottom with a craft knife, then loosens the slab and lifts it off the mold. The article is about a dish on a clay hump mold, not a ghost.
- 4.1: Pinching- The Most Ancient Technique — University of the Pacific (Jessica Fong, Ceramics course on Humanities LibreTexts). Pinch pot steps, hollow sphere project and amphora project. Supports: The course says to start from a fist-sized ball of well-wedged clay, press a thumb into the center, and rotate while pinching with equal pressure until the walls are roughly 1/4 inch thick, noting that uneven pinching gives lopsided or weak forms. It says to score and slip all connecting surfaces for a strong bond, to cut a small vent hole if a sphere is completely sealed to prevent explosions during firing, and to let a piece dry slowly before bisque firing. Its hollow sphere project builds two hemispheres from coils, joins them once both are leather-hard by scoring and slipping the edges, and blends the seam inside and out. It does not describe a ghost or a pumpkin.
- 4.4: Advanced Hand-building Techniques — University of the Pacific (Jessica Fong, Ceramics course on Humanities LibreTexts). Armatures, burnout and press-mold sections. Supports: The course says to keep the clay's thickness consistent to minimize stress during drying and firing, to carefully remove a hard armature if it is not designed to be left in during firing, to make vent holes so trapped air or moisture can escape, and to let a sculpture dry slowly and evenly. It does not describe a ghost and gives no wall-thickness figure.
- Drying Ceramics Without Cracks — Digitalfire, Tony Hansen. Ware shrinks when it dries; Isolate the stage where drying gradients are introduced; Give consideration to each type of piece; Clay is composed of microscopic flat crystals; Conclusion; and the picture notes on mugs, handles and foot rings. Supports: Hansen says it is the unevenness of drying, not its speed, that makes ware crack, and that at no time should any part of a piece be significantly ahead of another. A moisture spread introduced early (for example by an unshielded draft, or ware left out too long after forming) tends to remain, and in one of his examples covering mugs with cloth and plastic after the rims had stiffened did not save them. He recommends covering ware with cloth and plastic, waxing or wrapping handles so they keep pace with the body, slowing fast-drying sections with wax resist or latex at leather-hard, turning bowls over as soon as possible, even wall thickness with bases trimmed to the same thickness as the walls, avoiding sharp concave angles, and compressing the bottoms of wide thrown pieces to reduce drying stress (while saying even thickness and even drying, not compression, are the key). His conclusion: take cracked ware seriously, because a few cracked pieces can reveal a flawed process. The article gives no method for repairing a crack that has already opened. This is a technician's published explanation, not a test run for this site.
- Drying Shrinkage — Digitalfire, Tony Hansen. Opening glossary definition and the total-shrinkage example. Supports: Hansen says clays used in ceramics shrink when they dry because of particle packing as inter-particle water evaporates, and that excessive or uneven shrinkage causes cracks. He says a typical plastic pottery clay shrinks about 6% in drying, that highly plastic bodies can shrink up to about 7.5% before drying cracks become difficult to avoid, and that shrinkage can be reduced to 5% or below before plastic bodies become too difficult to form. He notes dry and fired shrinkage cannot simply be added: in his example 6.25 dry plus 6.66 fired would be 12.9, whereas the actual total shrinkage is 12.5%. This is a technician's published explanation, not a measurement for any one clay and not a test run for this site.
- Answers to 10 common air dry clay questions — Mont Marte (air dry clay manufacturer), FAQ, 09 Oct 2026. Answers 4, 5, 6, 8, 9 and 10. Supports: Mont Marte says air dry clay is not suitable for direct contact with an open flame or high heat, and that for a lantern or candle holder you should use a battery-operated LED tea light rather than a real candle, shaping the holder around the size of the LED light. It says the clay reaches earthenware hardness in around 24 hours depending on thickness, thicker pieces take longer, and you should wait until it is completely dry before painting. To limit cracks it says to dry gradually at room temperature away from direct heat or sunlight and keep thickness consistent. It says acrylic paint works well once the piece is completely dry. It says air dry clay is not food safe and should not be baked in an oven or kiln. This is one maker's advice for its own clay.
- 14 air dry clay techniques — Mont Marte (air dry clay manufacturer), Tips & Techniques, 03 Mar 2022. Slab building, slip, gluing, drying and bulking. Supports: Mont Marte says to roll air dry clay to an even thickness for a strong slab, that slip made from clay and water acts as a glue, and that small pieces pressed on may fall off once the clay dries, so craft glue can secure them. It says air dry clay typically takes 24 to 48 hours to dry, suggests flipping the piece at about 24 hours so it dries evenly, and warns against sun, a hairdryer or an oven. It says foil or polystyrene can bulk out a sculpture. This is one maker's advice for its own clay.
- DAS White — F.I.L.A. (Fabbrica Italiana Lapis ed Affini). Product description and format list (UK English page). Supports: FILA says DAS hardens on exposure to air without baking and can be moulded into solid, durable objects decorated with paints or multi-surface markers. It names bas-reliefs, sculptures, mosaics, and coating wood, metal, or glass as uses. Blocks are listed from 150 g to 1 kg. The page gives no drying time and no age label.
- Frequently Asked Questions — Creative Paperclay Co., Inc. Drying time, painting, sealing, and non-toxic answers. Supports: The FAQ says small, thin pieces may dry overnight while larger or thicker projects may take several days, and humidity can lengthen drying. It says a wide range of paints can be used and recommends spray lacquers or brush-on varnish. All its modeling materials carry the ACMI AP non-toxic seal; the FAQ gives no age label.
- Making Pottery Without a Wheel: A Guide to Wheel-Free Pottery Techniques — Clay King (ceramics supplier). Pinch pots, air-dry clay, and firing sections. Supports: Hand building shapes clay with hands and simple tools; the only requirement for pinch pots is the clay. Firing to bisque and again after glazing is essential for kiln clay, owning a kiln is often not feasible at first, and community studios or kiln rentals are alternatives. Air-dry clay needs no kiln but is not waterproof or food-safe.
- How to: fix cracks in air drying clay — Mont Marte (air dry clay manufacturer), Projects & How-to, 19 Aug 2021. Why does air dry clay crack?; How to fix cracks in air dry clay; How to keep air dry clay from cracking. Supports: Mont Marte says air dry clay cracks because it shrinks as its water evaporates, and that cracks are common. To fix one, it says to moisten the area with a little water (fingertips or a wet taklon brush), press in a small piece of fresh clay, smooth it with a wet brush, and let the piece dry completely. To prevent cracks, it advises letting the piece dry completely and evenly, turning it partway through drying or using a cake-style drying rack, and not making the clay too thin, aiming for about 1 cm. This is a manufacturer's how-to for air dry clay, not guidance for kiln-fired clay, and it was not tested for this site.
- Halloween Fire Safety Tips (safety tip sheet) — National Fire Protection Association (NFPA), Public Education Division, 2024. Halloween fire safety tips list and Did you know box. Supports: NFPA advises using a battery-operated candle or glow stick in jack-o'-lanterns, and keeping all decorations away from open flames and other heat sources. It says decorations are the first thing to ignite in more than 800 reported home fires each year, and nearly one-third of those fires were started by a candle.